SAN Health 3.2.6c not correctly identifying wwpn vendors
We have a number of pSeries systems, running under VIO, where we are using NPIV for the lpars. when we run SAN Health against our 48K directors, SAN health is identifying those WWPNs as being HP Tape...
View ArticleHelp interpreting MIB variable connUnitStatus
I am using fcmgmt.mib.what does snmp variable connUnitStatus value 5 means. fcmgmt defines connUnitStatus: Overall status of the connectivity unit. The goal of this object is to be the single poll...
View ArticleISL CRC Errors_ what is an acceptable threshold
One of the ISL cables we have laid seems to displaying CRC errors. We have since relaid it and the errors have reduced but not gone away. I've sent some data through this link and pasted the ports in...
View ArticleVirtual switch IP assignment
I have added IP addresses to my virtual switches, but the problem is that when I try to telnet or use SAN Health to any of new IPs I am still connected to FID 128 What is the proper way of...
View ArticleSAN Health - Incomplete fabric values exist for the fabric
I am trying to run SAN health against our DCX switches running 6.4.1b. When I "test fabric connectivity" it shows all the switches green but the fabric smiley remains red. If I try to run prelight...
View ArticleSan switch file system breaching more than 70%...Is there any action to be...
I need any supporting documents to justiy that switch file-system fill to full can cause a panic reboot. switch model:- SLKWRM0000490 Filesystem Size
View Articledoes not belong to a fabric in the tree view
HI Guys Just on-board with MY Brocade & Forum. Thanks to all who have supplied solutions and assistance during my 'lurking' :-) I have however got an issue that I cennot seem to find a solution...
View ArticleMeaning for Loopback->Port
Hello, last week when I get connected via telnet to one of our switches (silkworm4900) and when I executed a switchshow command, two of the 64 ports look like this: 15 15 id N1 Online Loopback->Port...
View Articleunused & defined nodes
Hi, im very new to Brocades and the report utility . I have run the report and have 200 pages of SAN health data. My aim was to find nodes which have been defined but are no longer in use. These need...
View Articlebrocade san switch vulnerability
Hi I have a customer that have been audited by a software company and the results were that the brocade san switch that he has in the san have vulnerability. The OS fabric of the san switch are 5.xx ....
View ArticleSAN Health Vs Cisco MDS 9124e
Our SAN is a hodgepodge of Brocade, McDATA and Cisco 9124e switches. When I use the SAN Health check it goes through all the motions and appears to be gathering data from the Cisco 9124e switches. But...
View ArticleChange report return email address
Hi, I generated a 24 hours SAN Health capture trying to diagnose a SAN related problem, after that I tried to upload and generate the report but never was succesful. I was trying to figure out what is...
View ArticleSwitch Reboot
I ran SAN Health against 6 switches... 5 without any issue but of for the sixth one it rebooted the switch.... not good. When I do an error dump I see a number of errors associated with the reboot but...
View ArticleSAN Health 3.2 is running ? at IBM 2027-256_Firmware : 06.03.02(EFCM V8.8)
Hi, I have IBM 2027-256 Director from old Mcdata. and I want to run SAN Health 3.2 Utility for this SAN Director My SAN Director is running at Firmware : 06.03.02(EFCM V8.8) Pls, guide me about...
View Articleunused & defined nodes
Hi, im very new to Brocades and the report utility . I have run the report and have 200 pages of SAN health data. My aim was to find nodes which have been defined but are no longer in use. These need...
View ArticleSH Version 2.2.1 Password Decryption bug
There is a bug within version 2.2.1 where the passwords are incorrectly decoded when loading a previously saved audit set. This problem will be rectified shortly in the release of version 2.2.2....
View Articlebrocade san switch vulnerability
Hi I have a customer that have been audited by a software company and the results were that the brocade san switch that he has in the san have vulnerability. The OS fabric of the san switch are 5.xx ....
View Articlehow can the SAN-Health-Report be sent to my email?
how can the SAN-Health-Report be sent to my email? when i can´t download it !!!
View ArticleFan Out Ratio
I ran SAN health and it looks great but... In the SAN summary details the 'Fan Out Ratio' for Host<!graemlin::D>isk comes up red :-( Does anyone knows what this exactly means and if this is...
View Article