Max perf and Average perf not show in SANHealth-report after 4GB/s ISL upgrade?
After we upgraded a couple of our ISL -links from 2GB/s to 4GB/s, I ran SANHealth performance analysis over 24 hours. I received the reports and the report claims that there hasn't been any traffic...
View ArticleClass 3 frames discarded
IN san health report I see C3D parameter = 78 on port details What indicate this counter?
View ArticleISL CRC Errors_ what is an acceptable threshold
One of the ISL cables we have laid seems to displaying CRC errors. We have since relaid it and the errors have reduced but not gone away. I've sent some data through this link and pasted the ports in...
View ArticleSAN Health Check with virtual fabrics?
I just tried to run a SAN Health Check but it failed to get most data because I'm using virtual fabrics, is there a way to make it aware of the virtual fabrics? Four switches, each with four virtual...
View ArticleHanging Zones/Alias/Config
Hello: I just ran SAN Health check today and in the "Zoming Metrics" section it states that I have. 21 Hanging Aliases 21 Hanging Zones 1 Hanging Config According to the explanation it means that I...
View ArticleVirtual switch IP assignment
I have added IP addresses to my virtual switches, but the problem is that when I try to telnet or use SAN Health to any of new IPs I am still connected to FID 128 What is the proper way of...
View ArticleSAN Health tool fails to connect to CMCNE/BNA Server
I have a bunch of fabrics in production and would like to connect the SAN Health tool to my CMCNE/BNA Server rather than managing these separately. I checked through the documentation
View ArticleMeaning for Loopback->Port
Hello, last week when I get connected via telnet to one of our switches (silkworm4900) and when I executed a switchshow command, two of the 64 ports look like this: 15 15 id N1 Online Loopback->Port...
View ArticleClear port error counter
Hello together, I use the Fabric/OS version v4.4.0b on our Directir 24000. With the command "porterrshow", I can see the error counters on each port from the director. I want to clear this counters,...
View ArticleEnc out
Hi folks, i just got back my SAN Heath report and i'm seeing a lot of host with high " ENC out". Can you give me some advise on what is going on. Do i need to put special options on my hosts. This is...
View ArticleSilkworm 3250 v4.4.0b_18
Hi all, I´m Looking for a manual to reset the password by Silkworm 3250 and how i can install the new firmware. I hope you can help me. Thanks
View Articlelatency and I/O timeouts
Hi there, I'm using b300 switches. I meet latency issues in my fabric. Brocade provides SAN Health, availables only with MS Windows. Does San Health will help me to find where latency issues occures...
View ArticleSAN Health Diagnostics on CiscoMDS9222i
Hi: I am trying to run the SAN Health Diagnostics on CiscoMDS9222i, with an error message - Not A Valid Switch Type.However the on support matrix ver 3.2.0 supports Cisco MDS 9222i. Can someone help...
View ArticleSAN health brings: possible unidentified switch found in fabric
hi, i have 2 fabrics: 1 fabric: 2x SAN24B-4 switches with FOS: 6.2.0e and 2x SAN40B-4 switches with FOS: 6.3.1b 2
View ArticleCapturing Port Statistics
Hi all, Hope someone can help. I'm a newbie to the community but dont hold that against me !. I use Brocade 200E and 4100E fibre switches. They are both running Fabric OS 5.2.0a. I'm trying to...
View ArticleDCX switches are shown as if nothing were connected to them
Hello, I've run a SAN Health in a customer's site and found that the DCX switches are shown as if nothing were connected to them, what is false. I think problem would be because we've virtual fabrics...
View ArticleIssues with San Health on a Cisco san
I have a 46 switch Cisco San. I am having issues getting San Health 3.2.2 to connect to all switches. It fails at the same command "show cfs peers" the switches are running a mix of 4.1.1b and 4.2.1b...
View ArticleFan Out Ratios what does it means
I received Fan Out ratios error. it has two parameters they are red color. 119:1 and 156.5:1 what does it means ???
View Articlebrocade san switch vulnerability
Hi I have a customer that have been audited by a software company and the results were that the brocade san switch that he has in the san have vulnerability. The OS fabric of the san switch are 5.xx ....
View ArticleWhat does "Hang Mems" mean?
Thumbing through my Zoning Details after running Brocade SAN Health, I notice some of my Zone Names are highlighted along with respective Zone Members, and they seem to corespond to Aliases Statistics,...
View Article