SAN HEALTH and ISL
Somebody say me what "Fan Out Ratios Dvc:ISL" means. i have 24:1 and the SAN Health report say me "Further investigation is necessary". What can i do ? Thank you.
View ArticleSan Health - Hang Mems
Hello, Do you know what Hang Mems that appears inside the report generated by SanHealth means ?
View ArticleIssues with San Health on a Cisco san
I have a 46 switch Cisco San. I am having issues getting San Health 3.2.2 to connect to all switches. It fails at the same command "show cfs peers" the switches are running a mix of 4.1.1b and 4.2.1b...
View Articleframe count & perf data - Enc Out?????
I ran a report that shows an attached server with blue highlighted Enc Out number of 2.2g. What is that? It's the only questionable item in the report... Thank you in advance!
View ArticleSend SAN Health data file (.bsh) via HTTPS
Dear eveybody, in my company we have SAN Health Version 3.2.2 and there's the possibility to send the encrypted SAN Health data file (.bsh) to the report generation queue via HTTPS. I click on the...
View ArticleSevere Latency Bottleneck issue on ISL connections:
“Severe latency bottleneck detected at slot 0, port 22” “Severe latency bottleneck detected at slot 0, port 23” This is showing up on our Principal switch (these are the two ISLs from a subordinate...
View ArticleSanhealth and logical switch/virtual fabric
Is there a way to configure sanhealth to scan all logical switches, and not only base switch? Our configuration is composed of DCX directors, in which we've defined logical switches and then virtual...
View ArticleSAN Health unable to capture information from DCX
I have a DCX connected to two separate SAN fabric (yes, this is not quite right, but just want to save costs). Say, it has physical IP x.x.x.1. Then I assign two virtual IPs x.x.x.2 and x.x.x.3 to the...
View ArticleDCX switches are shown as if nothing were connected to them
Hello, I've run a SAN Health in a customer's site and found that the DCX switches are shown as if nothing were connected to them, what is false. I think problem would be because we've virtual fabrics...
View ArticleHelp interpreting MIB variable connUnitStatus
I am using fcmgmt.mib.what does snmp variable connUnitStatus value 5 means. fcmgmt defines connUnitStatus: Overall status of the connectivity unit. The goal of this object is to be the single poll...
View ArticleVisio Professional 2007 cannot open VSD files from SAN Health
I've installed Visio Professional 2007, intending to use it on the VSD files from SAN Health (clinet 3.1.3, report builder 3.1.1). It refuses to open the files saying they were created with a new or...
View ArticleVirtual switch IP assignment
I have added IP addresses to my virtual switches, but the problem is that when I try to telnet or use SAN Health to any of new IPs I am still connected to FID 128 What is the proper way of...
View Article5100 running FOS 6.3.1a wont add to San Health Tree View
Hello, I have just bought a pair of 5100 switches 24 ports are licensed and have 8gb gbics installed these have come with version 6.3.1a FOS installed When I try to add them to my San Health...
View ArticleSAN Health Vs Cisco MDS 9124e
Our SAN is a hodgepodge of Brocade, McDATA and Cisco 9124e switches. When I use the SAN Health check it goes through all the motions and appears to be gathering data from the Cisco 9124e switches. But...
View ArticleCapturing Port Statistics
Hi all, Hope someone can help. I'm a newbie to the community but dont hold that against me !. I use Brocade 200E and 4100E fibre switches. They are both running Fabric OS 5.2.0a. I'm trying to...
View ArticleSAN Health 3.2 is running ? at IBM 2027-256_Firmware : 06.03.02(EFCM V8.8)
Hi, I have IBM 2027-256 Director from old Mcdata. and I want to run SAN Health 3.2 Utility for this SAN Director My SAN Director is running at Firmware : 06.03.02(EFCM V8.8) Pls, guide me about...
View ArticleSAN Health Report not showing 5480 internal ports
Hi I´m using SAN Health Version 3.2.4 with 2 x 5480 SAN Switches (HP 8/24 Blade SAN Switches) but, the report not show the internal ports of those switches. Only ports 0, 17, 18, 19, 20, 21, 22 and...
View ArticleCan you run Brocade SAN health check tool against Cisco switches with telnet...
Can you run Brocade SAN health check tool against Cisco switches with telnet disabled?
View ArticleSAN Health professional 1.0.0.6
I try to install SAN Health professional 1.0.0.6. During the installation I get a message version 1.0.0.6 will be installed. But when I start the program I have version1.0.0.5 installed. This...
View Article