Quantcast
Channel: Brocade Communities : Popular Discussions - SAN Health Utility
Browsing all 571 articles
Browse latest View live

does not belong to a fabric in the tree view

HI Guys   Just on-board with MY Brocade & Forum. Thanks to all who have supplied solutions and assistance during my 'lurking' :-) I have however got an issue that I cennot seem to find a solution...

View Article


Switch Reboot

I ran SAN Health against 6 switches... 5 without any issue but of for the sixth one it rebooted the switch.... not good. When I do an error dump I see a number of errors associated with the reboot but...

View Article


portshow

Interrupts:               42              Link_failure: 8         

View Article

Virtual switch IP assignment

I have added IP  addresses to my virtual switches, but the problem is that when I try to telnet or use SAN Health to any  of new IPs I am still connected to FID 128 What is the proper way of...

View Article

SAN HEALTH and ISL

Somebody say me what "Fan Out Ratios Dvc:ISL" means. i have 24:1 and the SAN Health report say me "Further investigation is necessary". What can i do ? Thank you.

View Article


Fan Out Ratio

I ran SAN health and it looks great but... In the SAN summary details the 'Fan Out Ratio' for Host<!graemlin::D>isk comes up red :-( Does anyone knows what this exactly means and if this is...

View Article

San Health - Hang Mems

Hello,   Do you know what Hang Mems that appears inside the report generated by SanHealth means ?

View Article

What does "Hang Mems" mean?

Thumbing through my Zoning Details after running Brocade SAN Health, I notice some of my Zone Names are highlighted along with respective Zone Members, and they seem to corespond to Aliases Statistics,...

View Article


Meaning for Loopback->Port

Hello, last week when I get connected via telnet to one of our switches (silkworm4900) and when I executed a switchshow command, two of the 64 ports look like this: 15 15 id N1 Online Loopback->Port...

View Article


-- ssh disable??

questiion - how i can disable the ssh service in SAN switches??

View Article

DCX switches are shown as if nothing were connected to them

Hello, I've run a SAN Health in a customer's site and found that the DCX switches are shown as if nothing were connected to them, what is false. I think problem would be because we've virtual fabrics...

View Article

SAN Health - Incomplete fabric values exist for the fabric

I am trying to run SAN health against our DCX switches running 6.4.1b. When I "test fabric connectivity" it shows all the switches green but the fabric smiley remains red. If I try to run prelight...

View Article

does not belong to a fabric in the tree view

HI Guys   Just on-board with MY Brocade & Forum. Thanks to all who have supplied solutions and assistance during my 'lurking' :-) I have however got an issue that I cennot seem to find a solution...

View Article


PreFlight Check Failure

Im trying to run SAn health on a new fabric we've adopted. The preflight check fails and gives the following error "Incomplete fabric values exist for the fabric Fabric A" I havent seen this before and...

View Article

Issues with San Health on a Cisco san

I have a 46 switch Cisco San. I am having issues getting San Health 3.2.2 to connect to all switches. It fails at the same command  "show cfs peers" the switches are running a mix of 4.1.1b and 4.2.1b...

View Article


Why supportshow is not included??

Hi, We have an installation with several brocade switches. One of the recomendations is to run supportshow frequently. The question is, why could not SANHealth be used with supportshow command? so from...

View Article

SAN Health "Port Use" ?

Can anyone help me with the Fabric Summary / Port Use / Port Speed section of a SAN Health report?  I have attached a pic of a Fabric Summary showing the Port Use / Port Speed columns.  What metric is...

View Article


Can I use SAN Health on a McData FC switch?

Can I use SAN Health on a McData FC switch? I just started a new job and they have some older Mcdata switches and I want to get the same info from them that I can get for the Silkworms...

View Article

Virtual switch IP assignment

I have added IP  addresses to my virtual switches, but the problem is that when I try to telnet or use SAN Health to any  of new IPs I am still connected to FID 128 What is the proper way of...

View Article

What happens when you select capture performance data?

What happens  when you select capture performance data?   Does the utility grab existing data from the switches? Or does it sit there and capture the data live?   I want to grab the last 8 hours of...

View Article
Browsing all 571 articles
Browse latest View live