I have a bunch of fabrics in production and would like to connect the SAN Health tool to my CMCNE/BNA Server rather than managing these separately. I checked through the documentation
↧
SAN Health tool fails to connect to CMCNE/BNA Server
↧
SAN Health unable to capture information from DCX
I have a DCX connected to two separate SAN fabric (yes, this is not quite right, but just want to save costs). Say, it has physical IP x.x.x.1. Then I assign two virtual IPs x.x.x.2 and x.x.x.3 to the virtual SAN switches. Each side connecting to another
↧
↧
Clearing SAN switch port statistics from web GUI
Hi All, please how do I clear the port statistics on the ports on an F16 2109 switch? I am having some serious errors showing up as loss of sync, loss of signals, encoding errors etc. Now I have made some changes to the fibre cables and configuration, I
↧
San switch file system breaching more than 70%...Is there any action to be taken pro-actively.
I need any supporting documents to justiy that switch file-system fill to full can cause a panic reboot. switch model:- SLKWRM0000490 Filesystem Size
↧
does not belong to a fabric in the tree view
HI Guys Just on-board with MY Brocade & Forum. Thanks to all who have supplied solutions and assistance during my 'lurking' :-) I have however got an issue that I cennot seem to find a solution of hint to so I am seeking guidance here.
↧
↧
Zoning issues ?
Hi, This is a great tool ! I have just a question, on my both fabrics, I have, in the Zoning Details in the Excel sheet, some Hanging aliases, zones and config. What's the meaning of this ? NOTE: This content was migrated by Brocade from the former
↧
Required SNMP configuration
Hi, I want to configure SNMP in my Brocade SW200E. Is it possible to generate a IO which will effect my production (existing LUN) environment due to snmp trap generation. Or is it possible to generate any bottleneck in my SAN. Any input should be
↧
Schedule SAN Health via windows 2008 task schedule
Hi, I am trying to run SAN Health as a scheduled task on windows 2008 server, but when I run the task I get the below error. ********* An error has occurred. 1) Check LAN connectivity and for information entered incorrectly into
↧
SAN Health unable to capture information from DCX
I have a DCX connected to two separate SAN fabric (yes, this is not quite right, but just want to save costs). Say, it has physical IP x.x.x.1. Then I assign two virtual IPs x.x.x.2 and x.x.x.3 to the virtual SAN switches. Each side connecting to another
↧
↧
What is Avg Perf and Max Perf on Fabric Tab?
Hi, could someone please tell me what those 2 parameters are? I assume they are percent of utilization? Ie 50% Avg Perf on a 8gb port would be 4gb? Though that doesnt explain why I have some Max Perfs over 100? Thank you!
↧
Severe Latency Bottleneck issue on ISL connections:
“Severe latency bottleneck detected at slot 0, port 22” “Severe latency bottleneck detected at slot 0, port 23” This is showing up on our Principal switch (these are the two ISLs from a subordinate switch). When I checked
↧
Zoning Details doesn't show aliases in zones
Has anybody else seen this? In the Zoning Details tab for a Fabric, the Defined Zones show the WWNs as opposed to the aliases that are defined in the zones.
↧
SAN Health 3.2.6c not correctly identifying wwpn vendors
We have a number of pSeries systems, running under VIO, where we are using NPIV for the lpars. when we run SAN Health against our 48K directors, SAN health is identifying those WWPNs as being HP Tape drives. All the WWPN's for the virtual
↧
↧
Syslog of Local7
I am using redhat linux to syslog my 3800 switches. However redhat uses local7 for its boot log and writes that info to the boot.log file. I would like to separate out the brocade messages to their own files. Any ideas? NOTE: This
↧
Discrepancy Between Sample Diagram & Actual
The SH sample Visio diagram shows switchports with the hardware detected on that port, the WWN, and what looks like an alias name. But all my reports show is the hardware detected on the port and the WWN. How do I get alias names to appear?
↧
Fan Out Ratio
I ran SAN health and it looks great but... In the SAN summary details the 'Fan Out Ratio' for Host<!graemlin::D>isk comes up red :-( Does anyone knows what this exactly means and if this is harmfull for the SAN ? For the rest our dual SAN
↧
SAN Health and Performance Chart?
Hi - I've recently used the SAN health utility and have received the analysis. When I check the performance/activity chart (MB/S) for the ports, the chart is completely blank - do I need to enable anything on the switch for it to capture this data
↧
↧
Long wave SFP doesn't work
Hi, I am new in Brocade world. Nice to meet all of you in this offical forum. I just got a 48K to install and all the short wave SFP works as I can see the red light in the SFP. However, the blue long SFP doesn't have the light on for some reason when
↧
SHDC 3.1.0 RELEASED
SAN health 3.1.0 is now available for download. Click To Download What’s new.... Support For the Mi10k, 5000 and Access Gateway. Added SSH support for the M4400 and M4700. Improved support for switches using Admin Domains. Support for the latest
↧
Failed to get Response From FabricShow
Having problems getting one particular McData 4400 to recognize in SAN Health. Get error "Failed to get Response From fabricShow", yet I can telnet fine to the switch and execute 'show fabric', 'show system' commands. I set the timeout values
↧