A portshow shows portPhys: 10 Mod_Val portScn: 2 Offline , and there is nothing connected, I'm hearing this is running diags, however Diag executing =
↧
A portshow shows Mod_Val
↧
San switch file system breaching more than 70%...Is there any action to be taken pro-actively.
I need any supporting documents to justiy that switch file-system fill to full can cause a panic reboot. switch model:- SLKWRM0000490 Filesystem Size
↧
↧
SAN Health 3.2.6c not correctly identifying wwpn vendors
We have a number of pSeries systems, running under VIO, where we are using NPIV for the lpars. when we run SAN Health against our 48K directors, SAN health is identifying those WWPNs as being HP Tape drives. All the WWPN's for the virtual
↧
Virtual switch IP assignment
I have added IP addresses to my virtual switches, but the problem is that when I try to telnet or use SAN Health to any of new IPs I am still connected to FID 128 What is the proper way of configuring the switch/SAN Health to allow
↧
Cable Unplugged
Connecting a Brocade 2800's ethernet port to a known working ethernet port on a system(using a known working ethernet cable), computer reports cable unplugged. I restarted the Brocade, same problem. Then I looked at the port, while it is for sure wide
↧
↧
Enhancement Request :: FTP the .bsh file
Good Morning, Would it be possible to ftp the .bsh files to a brocade ftp server instead of using the email method ? On my site, we often have issues with large attachments, and sometimes my bsh files are quite large. Thanks, Olivier NOTE: This
↧
ISL CRC Errors_ what is an acceptable threshold
One of the ISL cables we have laid seems to displaying CRC errors. We have since relaid it and the errors have reduced but not gone away. I've sent some data through this link and pasted the ports in question below (ouput is from porterrshow).
↧
ABORTED 101 - Session Disconnected while in module EFCM Login Routine
Hi anybody experienced the following message? 'ABORTED 101 - Session Disconnected while in module EFCM Login Routine' I have eighteen switches split across two fabrics. I get green smiley faces against all the switches and pre-flight runs OK but when
↧
SAN Health Check on Brocade 3900 Switch
Hello, IS SAN Health not supported on Brocade 3900 .. I am get following message:Probing failed on F-port which is possibly a privated device which is not supported in this port type. Pls let me know if there is any alternative
↧
↧
Duplicate WWN's being reported on SAN Health Check v3.2
Has anyone ran into this issue: After running a SAN Health report The SAN Port page shows multiple duplicate WWN's but when you do a switchshow the correct WWN are presented
↧
SAN Health Check performance capture does not progress
Has anyone experienced issues with SAN Health (v3.2.2) not collecting Performance Capture from their Brocade DCX's? There was a time that this capture used to work. However, suddenly this stopped working. What SAN Health does is that it
↧
Capturing Port Statistics
Hi all, Hope someone can help. I'm a newbie to the community but dont hold that against me !. I use Brocade 200E and 4100E fibre switches. They are both running Fabric OS 5.2.0a. I'm trying to capture to a [text] file the delta Port
↧
DCX switches are shown as if nothing were connected to them
Hello, I've run a SAN Health in a customer's site and found that the DCX switches are shown as if nothing were connected to them, what is false. I think problem would be because we've virtual fabrics in these DCXs switches, are Virtual Fabrics in DCX
↧
↧
What does "Hang Mems" mean?
Thumbing through my Zoning Details after running Brocade SAN Health, I notice some of my Zone Names are highlighted along with respective Zone Members, and they seem to corespond to Aliases Statistics, Zone Statics, and Config Statistics, and they all
↧
How to do Periodic Maintenance for Brocade SAN Switch B64/B80/384B/768B
I am a new Network Engineer. How to do Periodic Maintenance for Brocade 2005-B64 2498-B80 2499-384B 2499-768B SAN Switch? What items to check and what commands should be used. Is there formal papaer-format PM report? Thanks reall a lot to listen from
↧
SAN Health Check with virtual fabrics?
I just tried to run a SAN Health Check but it failed to get most data because I'm using virtual fabrics, is there a way to make it aware of the virtual fabrics? Four switches, each with four virtual fabrics, 128 as the chassis, 10 for the ISL
↧
SAN Health and Performance Chart?
Hi - I've recently used the SAN health utility and have received the analysis. When I check the performance/activity chart (MB/S) for the ports, the chart is completely blank - do I need to enable anything on the switch for it to capture this data
↧
↧
SAN HEALTH and ISL
Somebody say me what "Fan Out Ratios Dvc:ISL" means. i have 24:1 and the SAN Health report say me "Further investigation is necessary". What can i do ? Thank you.
↧
frame count & perf data - Enc Out?????
I ran a report that shows an attached server with blue highlighted Enc Out number of 2.2g. What is that? It's the only questionable item in the report... Thank you in advance!
↧
Fan Out Ratios what does it means
I received Fan Out ratios error. it has two parameters they are red color. 119:1 and 156.5:1 what does it means ???
↧