Would it be posible to separate out the perfromance monitoring piece as a small separate application ? There are many a time that type of almost real time perf monitoring would be beneficial especially since we don't currently have an SNMP tool to
↧
SAN Health request
↧
San Health and virtual switches
Hi How would I add virtual switches to San Health? I have 2 switches with 3 fabric IDs i.e 10,20,30 Thank you
↧
↧
Switches password encryption
Good Morning, I plan to create, on the fly, .set files, to have them always accurate with my sans configuration. Does anyone know how to encrypt the password in the set file ? Thanks, Olivier NOTE: This content was migrated by Brocade from the
↧
Clearing SAN switch port statistics from web GUI
Hi All, please how do I clear the port statistics on the ports on an F16 2109 switch? I am having some serious errors showing up as loss of sync, loss of signals, encoding errors etc. Now I have made some changes to the fibre cables and configuration, I
↧
Hanging Zones/Alias/Config
Hello: I just ran SAN Health check today and in the "Zoming Metrics" section it states that I have. 21 Hanging Aliases 21 Hanging Zones 1 Hanging Config According to the explanation it means that I have an element defined but SAN Health can't find the
↧
↧
SAN Health 3.2 is running ? at IBM 2027-256_Firmware : 06.03.02(EFCM V8.8)
Hi, I have IBM 2027-256 Director from old Mcdata. and I want to run SAN Health 3.2 Utility for this SAN Director My SAN Director is running at Firmware : 06.03.02(EFCM V8.8) Pls, guide me about to use or NOT this Utility
↧
Sanhealth not working for DCX directors
We are using SAN health 3.25 for capturing performance reports for our brocade switches. It is working fine for the othe brocade switches, but it is not working fine for the DCX directors. Whenever we try to run the report, after validating all the
↧
Severe Latency Bottleneck issue on ISL connections:
“Severe latency bottleneck detected at slot 0, port 22” “Severe latency bottleneck detected at slot 0, port 23” This is showing up on our Principal switch (these are the two ISLs from a subordinate switch). When I checked
↧
SAN Health tool fails to connect to CMCNE/BNA Server
I have a bunch of fabrics in production and would like to connect the SAN Health tool to my CMCNE/BNA Server rather than managing these separately. I checked through the documentation
↧
↧
Issues with San Health on a Cisco san
I have a 46 switch Cisco San. I am having issues getting San Health 3.2.2 to connect to all switches. It fails at the same command "show cfs peers" the switches are running a mix of 4.1.1b and 4.2.1b code. Any known issues or gottchas i need to be
↧
Zoning Details doesn't show aliases in zones
Has anybody else seen this? In the Zoning Details tab for a Fabric, the Defined Zones show the WWNs as opposed to the aliases that are defined in the zones.
↧
Zoning issues ?
Hi, This is a great tool ! I have just a question, on my both fabrics, I have, in the Zoning Details in the Excel sheet, some Hanging aliases, zones and config. What's the meaning of this ? NOTE: This content was migrated by Brocade from the former
↧
san health don't work correctly with AdminDomain
I use AD in Fos5.2.0.a San Health ignore all device which are in AD. The reports are unusable NOTE: This content was migrated by Brocade from the former Brocade Connect community on March 10, 2008, on behalf of the author.
↧
↧
IS SAN HEATH support Connectrix ED-64M (McDATA ED-6064) switches ?
Hi, COuld you telle me if SAN health could be used on ED64M/ED6064 ? Regards William
↧
Silkworm 3250 v4.4.0b_18
Hi all, I´m Looking for a manual to reset the password by Silkworm 3250 and how i can install the new firmware. I hope you can help me. Thanks
↧
San Health and virtual switches
Hi How would I add virtual switches to San Health? I have 2 switches with 3 fabric IDs i.e 10,20,30 Thank you
↧
5100 running FOS 6.3.1a wont add to San Health Tree View
Hello, I have just bought a pair of 5100 switches 24 ports are licensed and have 8gb gbics installed these have come with version 6.3.1a FOS installed When I try to add them to my San Health fabric set, San Health telnets too them
↧
↧
SAN Health Report info
Does the SAN Health Report show the mac address of the Brocade switch? If not is there a way to find out what the mac address is, we have a 200e..
↧
SAN Health Check performance capture does not progress
Has anyone experienced issues with SAN Health (v3.2.2) not collecting Performance Capture from their Brocade DCX's? There was a time that this capture used to work. However, suddenly this stopped working. What SAN Health does is that it
↧
SAN Health professional 1.0.0.6
I try to install SAN Health professional 1.0.0.6. During the installation I get a message version 1.0.0.6 will be installed. But when I start the program I have version1.0.0.5 installed. This happens on a PC where I try to update
↧