HI Guys Just on-board with MY Brocade & Forum. Thanks to all who have supplied solutions and assistance during my 'lurking' :-) I have however got an issue that I cennot seem to find a solution of hint to so I am seeking guidance here.
↧
does not belong to a fabric in the tree view
↧
Switch Reboot
I ran SAN Health against 6 switches... 5 without any issue but of for the sixth one it rebooted the switch.... not good. When I do an error dump I see a number of errors associated with the reboot but the main one is - Error 01 ---- 0x103bd480
↧
↧
portshow
Interrupts: 42 Link_failure: 8
↧
Virtual switch IP assignment
I have added IP addresses to my virtual switches, but the problem is that when I try to telnet or use SAN Health to any of new IPs I am still connected to FID 128 What is the proper way of configuring the switch/SAN Health to allow
↧
SAN HEALTH and ISL
Somebody say me what "Fan Out Ratios Dvc:ISL" means. i have 24:1 and the SAN Health report say me "Further investigation is necessary". What can i do ? Thank you.
↧
↧
Fan Out Ratio
I ran SAN health and it looks great but... In the SAN summary details the 'Fan Out Ratio' for Host<!graemlin::D>isk comes up red :-( Does anyone knows what this exactly means and if this is harmfull for the SAN ? For the rest our dual SAN
↧
San Health - Hang Mems
Hello, Do you know what Hang Mems that appears inside the report generated by SanHealth means ?
↧
What does "Hang Mems" mean?
Thumbing through my Zoning Details after running Brocade SAN Health, I notice some of my Zone Names are highlighted along with respective Zone Members, and they seem to corespond to Aliases Statistics, Zone Statics, and Config Statistics, and they all
↧
Meaning for Loopback->Port
Hello, last week when I get connected via telnet to one of our switches (silkworm4900) and when I executed a switchshow command, two of the 64 ports look like this: 15 15 id N1 Online Loopback->Port 15 40 40 id N1 Online Loopback->Port 40 When I
↧
↧
-- ssh disable??
questiion - how i can disable the ssh service in SAN switches??
↧
DCX switches are shown as if nothing were connected to them
Hello, I've run a SAN Health in a customer's site and found that the DCX switches are shown as if nothing were connected to them, what is false. I think problem would be because we've virtual fabrics in these DCXs switches, are Virtual Fabrics in DCX
↧
SAN Health - Incomplete fabric values exist for the fabric
I am trying to run SAN health against our DCX switches running 6.4.1b. When I "test fabric connectivity" it shows all the switches green but the fabric smiley remains red. If I try to run prelight checks it throws up the error "Incomplete fabric values
↧
does not belong to a fabric in the tree view
HI Guys Just on-board with MY Brocade & Forum. Thanks to all who have supplied solutions and assistance during my 'lurking' :-) I have however got an issue that I cennot seem to find a solution of hint to so I am seeking guidance here.
↧
↧
PreFlight Check Failure
Im trying to run SAn health on a new fabric we've adopted. The preflight check fails and gives the following error "Incomplete fabric values exist for the fabric Fabric A" I havent seen this before and am a little unsure of where to start. Thanks in
↧
Issues with San Health on a Cisco san
I have a 46 switch Cisco San. I am having issues getting San Health 3.2.2 to connect to all switches. It fails at the same command "show cfs peers" the switches are running a mix of 4.1.1b and 4.2.1b code. Any known issues or gottchas i need to be
↧
Why supportshow is not included??
Hi, We have an installation with several brocade switches. One of the recomendations is to run supportshow frequently. The question is, why could not SANHealth be used with supportshow command? so from a single place I can gather the supportshow of all
↧
SAN Health "Port Use" ?
Can anyone help me with the Fabric Summary / Port Use / Port Speed section of a SAN Health report? I have attached a pic of a Fabric Summary showing the Port Use / Port Speed columns. What metric is this section using? Switchshow does
↧
↧
Can I use SAN Health on a McData FC switch?
Can I use SAN Health on a McData FC switch? I just started a new job and they have some older Mcdata switches and I want to get the same info from them that I can get for the Silkworms...
↧
Virtual switch IP assignment
I have added IP addresses to my virtual switches, but the problem is that when I try to telnet or use SAN Health to any of new IPs I am still connected to FID 128 What is the proper way of configuring the switch/SAN Health to allow
↧
What happens when you select capture performance data?
What happens when you select capture performance data? Does the utility grab existing data from the switches? Or does it sit there and capture the data live? I want to grab the last 8 hours of performace data. So I'm hoping
↧